Print

[Travellin Dave]

Good morning, men.

Morning Uncle Tone.

How's the bathroom coming, Mark? Getting ready to finish a basement here. Just completely clearing it out for now. Eventually, the bathroom will be built.

A couple of towel bars (on order) and f'n crown molding left to finish.  And the wife still has to pick out some mirrors.  And two medicine cabinets.  And, and, and......

I hear ya. I've done quite a bit of crown molding work. It's a pain in the ass. The secret is building a good jig so that you cut each piece at the same angle. I have two saws for that. Not sure where either of them are but I suspect I will find them this week.

I cheat and cut it at work.  We have a miter saw table setup which works well. So it's not the cutting part as much as the installing part which sucks. These are cabinets, not wall/ceiling molding.

Well, that and checking for the this side up arrows....

The warden ordered the cabinets.  I have no idea if they were available with the crown molding pre-installed.  Sorta doubt it, but that would have been the ticket for sure.

No such thing, how would you hang multiples? Rookies, sheesh

Where's logic come into it?

If you are hanging a run of cabinets, or just more than one, how are the cabinets going to butt to each other if crown goes around 3 sides. If crown is only on the fronts, there are seams at every cabinet and how would you return the side to the wall at the end of a run when the fronts are cut square at the end of the cabinet?

This is a bathroom, not a kitchen.  How many friggin cabinets do you have to hang.  What all you storing in there?  Putting in a wardrobe for costumes as well?

Doesn't matter, it's the reason they don't sell cabinets with crown attached. I've completely lost interest in this subject

Someone say hinges and feet?

Feet don't come on cabinets.  They are supposed to be part of tower humidors however.

[Travellin Dave]

GMornin fellas

Morning CG  - How bout that NDS - 5 in a row!

Indeed, glad to see you beat your Gamecocks as well.

Hopefully the big orange can get it done tonight!!!

Sure hope so.

They've got my vote!

I'll refrain from cheering for them, for Dave's sake. If the Bengals and Vikings are any indication, me rooting for a team leads to a painful demise.

No shit right - those Vikings...words can't describe that heartbreak.

#lacesoutdan

Both teams found very Browns ways to lose, no question.

Truth to that - just a bad way to lose.  Didn't score a touchdown all day, hard to blame a kicker who goes 3/4 in sub zero temps all day, but that's the 'life of a kicker'.

And those poor bastiges are usually near the bottom of the pay scale too.

He won them a couple of games this year too, so I hope he is still with the team next year.

The damn holder should be canned. He botched the hold in 3 of the 4 kicks. The kicker was lucky he made anything all day, when you add the shitty holds to the shitty weather.

The kicker shit the bed, nerves got the best of him on that kick. He hurried it and yanked the kick, plain and simple.

Yipped It Left Right?

We call it a 'pull hook' in the golf world

If you meant to do it, call it a draw... when you don't, snap hook.

Hey CG. How's about those BI-Zun! Not even close.

Just remember, it's Bi-Zon not Biceson
and Clem-Son, not Clem-Zen.  (Clemp-Son is also acceptable for old schoolers)

[BackyardSmoker]

Using a coping saw is a lost art, but I don't like to brag. 

What's a coping saw?

A saw that allows you to cope with even the worst of situations...

He's lost interest already.

[Travellin Dave]

Golf goin' for the Oscuros today, huh...

That just means someone else will get a good deal

[Travellin Dave]

Golf goin' for the Oscuros today, huh...

That just means someone else will get a good deal

But a slightly worse deal than I would've gotten.

Somebody currently winning at 34?

[Travellin Dave]

Morning Sam and Steve.

[LuvTooGolf]

Golf goin' for the Oscuros today, huh...

That just means someone else will get a good deal

But a slightly worse deal than I would've gotten.

Somebody currently winning at 34?

Yeah, me. I just meant if they outbid me, they'd get a slightly worse deal. Cause they'd be paying more.

[BackyardSmoker]

Golf goin' for the Oscuros today, huh...

That just means someone else will get a good deal

But a slightly worse deal than I would've gotten.

Haha... slightly. MrAtlantic took his at $43.

[Travellin Dave]

Golf goin' for the Oscuros today, huh...

That just means someone else will get a good deal

But a slightly worse deal than I would've gotten.

Somebody currently winning at 34?

Yeah, me. I just meant if they outbid me, they'd get a slightly worse deal. Cause they'd be paying more.

Yea, saw that so I held back.

[A Friend of Charlie]

Just saw that David Bowie has died.
Just released an album this week as well.

Oh shit, really?!?

[LuvTooGolf]

Golf goin' for the Oscuros today, huh...

That just means someone else will get a good deal

But a slightly worse deal than I would've gotten.

Somebody currently winning at 34?

Yeah, me. I just meant if they outbid me, they'd get a slightly worse deal. Cause they'd be paying more.

Yea, saw that so I held back.

You're a fine human being. Though, SharkFish may not agree. 

[A Friend of Charlie]

Good morning, men.

Morning Uncle Tone.

How's the bathroom coming, Mark? Getting ready to finish a basement here. Just completely clearing it out for now. Eventually, the bathroom will be built.

A couple of towel bars (on order) and f'n crown molding left to finish.  And the wife still has to pick out some mirrors.  And two medicine cabinets.  And, and, and......

I hear ya. I've done quite a bit of crown molding work. It's a pain in the ass. The secret is building a good jig so that you cut each piece at the same angle. I have two saws for that. Not sure where either of them are but I suspect I will find them this week.

I cheat and cut it at work.  We have a miter saw table setup which works well. So it's not the cutting part as much as the installing part which sucks. These are cabinets, not wall/ceiling molding.

Well, that and checking for the this side up arrows....

The warden ordered the cabinets.  I have no idea if they were available with the crown molding pre-installed.  Sorta doubt it, but that would have been the ticket for sure.

No such thing, how would you hang multiples? Rookies, sheesh

Where's logic come into it?

If you are hanging a run of cabinets, or just more than one, how are the cabinets going to butt to each other if crown goes around 3 sides. If crown is only on the fronts, there are seams at every cabinet and how would you return the side to the wall at the end of a run when the fronts are cut square at the end of the cabinet?

I wasn't clear. I was sarcastically saying, where does logic fit into our discussion?

[LuvTooGolf]

Good morning, men.

Morning Uncle Tone.

How's the bathroom coming, Mark? Getting ready to finish a basement here. Just completely clearing it out for now. Eventually, the bathroom will be built.

A couple of towel bars (on order) and f'n crown molding left to finish.  And the wife still has to pick out some mirrors.  And two medicine cabinets.  And, and, and......

I hear ya. I've done quite a bit of crown molding work. It's a pain in the ass. The secret is building a good jig so that you cut each piece at the same angle. I have two saws for that. Not sure where either of them are but I suspect I will find them this week.

I cheat and cut it at work.  We have a miter saw table setup which works well. So it's not the cutting part as much as the installing part which sucks. These are cabinets, not wall/ceiling molding.

Well, that and checking for the this side up arrows....

The warden ordered the cabinets.  I have no idea if they were available with the crown molding pre-installed.  Sorta doubt it, but that would have been the ticket for sure.

No such thing, how would you hang multiples? Rookies, sheesh

Where's logic come into it?

If you are hanging a run of cabinets, or just more than one, how are the cabinets going to butt to each other if crown goes around 3 sides. If crown is only on the fronts, there are seams at every cabinet and how would you return the side to the wall at the end of a run when the fronts are cut square at the end of the cabinet?

I wasn't clear. I was sarcastically saying, where does logic fit into our discussion?

Or any of our discussions, for that matter.

[A Friend of Charlie]

Good morning, men.

Morning Uncle Tone.

How's the bathroom coming, Mark? Getting ready to finish a basement here. Just completely clearing it out for now. Eventually, the bathroom will be built.

A couple of towel bars (on order) and f'n crown molding left to finish.  And the wife still has to pick out some mirrors.  And two medicine cabinets.  And, and, and......

I hear ya. I've done quite a bit of crown molding work. It's a pain in the ass. The secret is building a good jig so that you cut each piece at the same angle. I have two saws for that. Not sure where either of them are but I suspect I will find them this week.

I cheat and cut it at work.  We have a miter saw table setup which works well. So it's not the cutting part as much as the installing part which sucks. These are cabinets, not wall/ceiling molding.

Well, that and checking for the this side up arrows....

The warden ordered the cabinets.  I have no idea if they were available with the crown molding pre-installed.  Sorta doubt it, but that would have been the ticket for sure.

No such thing, how would you hang multiples? Rookies, sheesh

Where's logic come into it?

If you are hanging a run of cabinets, or just more than one, how are the cabinets going to butt to each other if crown goes around 3 sides. If crown is only on the fronts, there are seams at every cabinet and how would you return the side to the wall at the end of a run when the fronts are cut square at the end of the cabinet?

I wasn't clear. I was sarcastically saying, where does logic fit into our discussion?

Or any of our discussions, for that matter.

#cabinettalk

[sfish]

Using a coping saw is a lost art, but I don't like to brag. 

U are probably one of 5 under age 100 if you. can use one well

Not true, it's still the only way to get a tight inside corner on crown (If you know what you're doing)